When you’re driving your go-kart around the track, you want to make sure you’re hitting your targets as closely as possible. That’s why it’s so important to have a good speedometer installed on your kart. If you don’t have a speedometer, you may not know how fast you’re going. And if you don’t know how fast you’re going, there’s a good chance you could end up in an accident. So read on to learn how to install a speedometer on a go-kart.
What is a Speedometer?
A speedometer is a device that measures the speed of a vehicle. It may be mounted in the vehicle or attached to the drivetrain. Speedometers can be analog or digital and can display mph, kph, or another unit of measurement.
How Does a Speedometer Work?
A speedometer is a device that measures the speed of a vehicle. The most common type of speedometer is an analog device, which measures the number of rotations per minute (RPM) the engine is making. Digital speedometers use microprocessors to measure the RPMs and can be more accurate than analog devices.
To install a speedometer on a go-kart, first, determine the size of the hole needed in the kart’s chassis. Next, remove the old speedometer from the kart. If the old speedometer was attached to a cable, cut off the cable and discard it. If the old speedometer was glued to the chassis, remove it gently with a screwdriver or pliers. Once the old speedometer is removed, mark where the new speedometer will need to be placed on the chassis using a drill bit or punch. Center the new speedometer on this mark and screw it into place using screws or bolts. Tighten these screws or bolts until they are slightly tight but not so tight that they cause damage to the kart or Speedometer; otherwise, replace these screws or bolts with new ones later on if needed. Finally, reinstall any front or rear lights that were removed during installation and secure them using screws or bolts.
How to Install a Speedometer on a GoKart
Installing a speedometer on your go-kart can give you an accurate reading of your speed, so you know where you stand in relation to the other go-karts around you. The installation process is simple, but it does require some assembly. Here’s how to do it:
1. Open the hood of your kart and locate the engine. There will likely be a screw holding down the speedometer bracket. Remove the screw and set it aside.
2. Take the speedometer bracket and remove the four screws that fasten it to the engine. Be sure to save these screws!
3. Carefully pull the speedometer off of the engine and set it aside. You’ll need to replace this part later if you decide to change speeds (more on that later).
4. Now start assembling the new speedometer bracket by positioning it over one of the original screws and securing it with another screw from your kit. Make sure that all four corners of the bracket are secure before tightening down the final screw. If everything goes according to plan, your newly installed speedometer should now be ready for use!
Here is a quick summary for installing a speedometer on a go-kart:
1. Mount Speedometer
Installing a speedometer on a go-kart can be a lot of fun, and it’s an easy project that can be done in just a few minutes. Before you start, make sure that your go-kart has the correct size speedometer. If your kart doesn’t have a factory-installed speedometer, you will need to purchase one separately. The following steps will show you how to install a speedometer on your go-kart:
1) Locate the bolts that hold the speedometer bracket to the kart’s frame. Remove the bolts and set them aside.
2) Next, remove the dirt grip from the back of the speedometer bracket. This will allow you to mount the bracket onto the kart more easily.
3) Slide the bracket over the frame until it snaps into place in between the rear axle and wheel hub. Make sure that it is sitting level with both ends of its track.
4) Replace the dirt grip onto the back of the bracket and screw it into place using two screws (that you removed from step 1).
5) Align and center the speedometer within its bracket by adjusting its position until it lines up perfectly with markings on either side of its track.
6) Replace all four bolts that hold down the speedometer bracket to ensure stability.
2. Install RPM Sensor
There are a few things you will need before beginning this installation: an RPM sensor, an adaptor, and a wrench. The RPM sensor is the most important part of this project, so be sure to purchase one that is compatible with your go-kart.
To install the RPM sensor, first, remove the panel that covers the speedometer. On many models, it can be removed by popping it off with a screwdriver. Once the panel is off, unscrew the two screws that hold the sensor in place and remove it.
Next, connect the RPM sensor to the adaptor using the supplied wiring instructions. Reattach the panel and screws and you’re ready to go!
3. Install Distance & Speed Calculator
If you are installing a speedometer on your GoKart, you will need to measure the distance and speed of your track. The tool you need for this is a speedometer installation kit. The following instructions will show you how to install a speedometer on a GoKart.
To begin, remove the three screws that hold the rear light cover in place. Next, remove the rear light cover. On some models, there may be additional fasteners holding the cover in place. Once the light cover is removed, you will see the motor assembly and gearbox (if present). Beneath these components is the speedometer sensor. To access this sensor, first, remove the two screws that hold it in place and then lift it out of its mount.
Once the sensor is free, measure its length and width and make a sketch or diagram of where it should go on your GoKart. You will also need to determine how wide and long of an opening you want for the sensor in your car. Once you have made all of these measurements, use a drill bit that is slightly wider than the width of your speedometer mounting bracket and insert it into your drill while turning it by hand to create an accurate hole in which to mount your sensor. Make sure that both ends of the bracket fit snugly into their respective holes in the car bodywork so that there are no gaps between them when they are screwed together. Finally, screw the bracket into place using Phillip’s head.
How To Set the Tire Measurements on Your Speedometer
Speedometer installation on a GoKart is not difficult, but it does require that you take some measurements. The following are the steps to installing a speedometer on your vehicle:
1. Measure the outside circumference of the wheel at its widest point. This measurement will be used in determining the mounting hole size.
2. Take the outer measurement and divide by 2 to get the inside diameter of the mounting hole. This will be used in determining the bolt size.
3. Measure the height of the wheel from the ground to the center hub spindle, using a straight edge or yardstick of an appropriate length (this will determine the bolt height). The bolt height should be just below the center hub spindle if possible.
4. Determine if your speedometer uses external or internal gears (most do not use gears). If using external gears, remove them and set them aside for later use (you will need to attach them back onto the speedometer). If using internal gears, proceed with the installation instructions below for either type of gearbox.
5. Mark mounting holes on side of the wheel with a pencil or dry-erase marker. Drill holes accordingly with standard household screws (self-tapping screws work well) into the side of the wheel – being sure to drill out the ENTIRE HOLE before screwing in the screw! Do NOT over-tighten screws – they may strip wheel threading!
6. Thread bolts into mounting holes and tighten them securely with the wrench provided (a washer and nut should also be supplied).
4. Install Temperature Sensor (Optional)
If you have added a temperature sensor to your GoKart, you will need to install the sensor before proceeding. To do this, first, remove the cover on the back of the speedometer. There is a screw at the top and bottom that should be removed. Next, remove the four screws that hold the sensor in place. Finally, unplug the sensor’s connector and replace it with the one that came with your kit. Reconnect all of the wiring harnesses and screws and you are finished!
5. Attached to Battery (Optional)
Installing a speedometer on a GoKart can be a fun and easy project for the mechanically inclined. The steps involved are relatively simple, and the end result is a more accurate measurement of your kart’s speed.
1. Remove the front bumper cover by unscrewing the four screws that hold it in place.
2. Disconnect the negative battery cable from the battery.
3. Remove the two bolts that hold the speedometer housing to the chassis.
4. With the speedometer housing off of the chassis, you can now install or remove your new speedometer using standard installation procedures. Be sure to read your speedometer’s instructions before installation for specific details about how it should be mounted and secured to your kart.
5. Replace the speedometer housing bolts and screws, and reattach the front bumper cover.
6. reconnect the negative battery cable and test your new speedometer by driving your kart around the track.
Congratulations! You have installed a speedometer on your GoKart. The results of your test will now provide you with an accurate measurement of your kart’s speed.
6. Setup Your Speedometer
Installing a speedometer on your kart is an easy and cost-effective way to improve your driving experience. There are a few different types of speedometers available, so be sure to choose the one that is compatible with your kart.
To install a speedometer, you first need to remove the factory unit. Usually this involves removing four screws and popping the unit off the chassis. Be sure to save all of the wiring connections!
Next, you’ll need to find a compatible sensor. The most common type of sensor uses infrared light to track vehicle speed. You can buy sensors from various online retailers or from local hobby shops. Once you have acquired the sensor, install it in accordance with the manufacturer’s instructions.
Finally, mount the speedometer onto the chassis using screws and brackets supplied with the unit. Reconnect all of the wiring harnesses and replace the factory unit if necessary. You’re now ready to start tracking your vehicle’s speed!
Conclusion
If you’re looking to increase your speed while driving your kart, installing a speedometer is the perfect solution. By adding this component to your kart, you can track your exact speed and improve your performance dramatically.
If you’re looking to install a speedometer on your go-kart, there are a few things you’ll need before getting started. First, you’ll need to gather the following items: a speedometer, an installation kit, and bolt cutters. Second, you’ll need to remove the engine cover on your go-kart. Third, you’ll need to unscrew the two mounting bolts that hold the engine cover in place. Fourth, you’ll need to slide the speedometer onto the mounting bolts and tighten them into place with the included installation kit. Finally, reinstall the engine cover and screw it in place with bolt cutters. Congratulations! You’ve just installed your very own speedometer on your go-kart!